Exactly How to Install a Bathtub
Exactly How to Install a Bathtub
Blog Article
We have stumbled on this great article relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the net and reckoned it made sense to share it with you over here.
Setting up a bath tub isn't specifically rocket science, however it does need strong plumbing, woodworking, and also sometimes, tiling skills. Changing an old tub with a brand-new one is additionally a moderately difficult project. If the old tub is easily easily accessible, the job can relocate easily; if you have to open a wall to remove the old tub as well as place the brand-new tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to move out the old tub as well as set in the new one. Make certain you have actually certified yourself for the job and are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed task, it is far better to take into consideration using one prior to you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will help you install a new bath tub in your washroom if you have actually currently gotten a brand-new tub and don't need to transform the setup of your previous water system pipelines.
Your tools as well as product list must make up the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the water. After doing so, activate the taps to drain any water continuing to be in the system. The procedure of removing the existing taps can be fairly troublesome as a result of the limited accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in location in between the tap and also the sink. Protect the faucet in place with the supplier supplied backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet ports. The previous type must be connected to the faucet finishes first, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Tub
Utilizing both wooden boards under its feet, place the tub in the required setting. The wood boards are helpful in evenly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to guarantee that the bath tub is leveled all round. This can be attained by checking the spirit level as well as changing the feet on the bath tub till the level reads level.
To set up faucets, fit all-time low of the outermost adaptable faucet connector to the suitable supply pipeline by making a compression sign up with; after that do the very same for the other tap.
Switch on the supply of water as well as inspect all joints and also new pipework for leaks and tighten them if required. Fill up the tub and likewise inspect the overflow electrical outlet as well as the typical electrical outlet for leakages.
Ultimately, take care of the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub should wait until the bathtub has been used at least once as this will certainly resolve it right into its last position.
Preparing for the Installation
Firstly, the supporting structure provided with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to avoid strain on the bathtub.
Fit the adaptable faucet ports to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you use every one of the provided washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final position.
Tiling Around the Tub
In the area where the bathroom satisfies the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, causing complications with moisture and feasible leaks to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components as well as fittings. They are offered in tubes and cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked paper or soft rope. Bear in mind to always load the tub with water prior to securing, to allow for the activity experienced when the tub is in usage. The sealant can split rather very early if you do not take into account this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been shown that article on Installing A Bathtub from someone on our other domain. Sharing is good. Who knows, you might be helping someone out. Thanks so much for your time invested reading it.
Click Here To Read More Report this page